PDA

View Full Version : JKS Sway bar disconnects


Ash74
23-06-11, 07:27 PM
G'day

As per my recent damage to my original sway bar links and repair by TBN8R, I am in the future, going to purchase some disconnects, after contacting wooders they are concerned about my OME 2" lift as they have heard that the OME can give you more lift then claimed, and unfortunately i did not measure before and after. Should I go with the JKS 0-2" or the 2.5-4"?
85cj7
23-06-11, 08:17 PM
0-2". Your springs will settle after time plus the weight of gear/passengers and additional mods down the line ( ie. bumpers, winch, cage) will further compress your springs giving you less lift.

Unless of course you foresee yourself running a larger lift in the immediate future then I would go with the 2.5-4". It depends on YOUR future plans and needs.
Ash74
23-06-11, 08:41 PM
85cj 7
the only other mod that I will be doing anytime soon is larger tyres 35's if possible, will the 0-2" still be ok?
SKIZZI
23-06-11, 08:45 PM
I recon go the 2.5 - 4 and set them on the shortest setting.
Wooders
24-06-11, 08:43 AM
0-2". Your springs will settle after time plus the weight of gear/passengers and additional mods down the line ( ie. bumpers, winch, cage) will further compress your springs giving you less lift.

Unless of course you foresee yourself running a larger lift in the immediate future then I would go with the 2.5-4". It depends on YOUR future plans and needs.
Bang on the money this advice.
85cj7
24-06-11, 10:09 AM
85cj 7
the only other mod that I will be doing anytime soon is larger tyres 35's if possible, will the 0-2" still be ok?

Larger tires does not give you more suspension lift just further lift from the ground. So you would still have 2" of suspension lift. As long as you aren't going to be playing with the suspension then my previous comment stands.
Ash74
24-06-11, 12:54 PM
Thanks guys
Ash74
10-07-11, 05:21 PM
888886885885884
887Guys

I got myself a set of disconnects from wooders on Thursday and have just put them on. I got the 2 inch set as advised but did have to adjust to get the sway bay as close as 0 degree as my eye could see. Can you please have a look at my photos and advise if they look correct?
Steve F
10-07-11, 05:55 PM
As long as the swaybar is level, or slightly up, then you should be fine.

Cheers
Steve
Ash74
10-07-11, 06:46 PM
Steve

When I took the originals off the swaybar was well under level.

If anytghing its probably slightly under level now, easy enough to take off and do again.
Ash74
10-07-11, 06:48 PM
Steve

Also

Do I treat the passenger side as the passenger side or is it reverse due to being an american product?
TRBN8R
10-07-11, 11:53 PM
Looks right to me as per installation instructions http://www.jksmfg.com/support/install_qrd_pn2030_2034.pdf Just their passenger side is our driver side.......... Next time u r out with friends just take them off, swing the swaybar to its highest position and see the improvement in flex......
Ash74
11-07-11, 04:11 PM
Mani
G'day
Not thinking American, I have place the squared off lower mounting post on the passenger side and the Tapered lower mounting post on the drivers side. Is this correct for the Aussie model?
stevet
11-07-11, 05:58 PM
Been corrected so to speak....;D......... B..:)..y JK owners.:D.........:).....
Glass's upgrade next on list...:D..........:)...
bogged
11-07-11, 05:59 PM
The photo is correct. The lower pins face inwards ie: remove to the centre of the vehicle.







And yes,


The US passenger side is our drivers side, so reverse where applicable.
TRBN8R
12-07-11, 01:05 AM
Mani
G'day
Not thinking American, I have place the squared off lower mounting post on the passenger side and the Tapered lower mounting post on the drivers side. Is this correct for the Aussie model?

Hi Ash,

If u can put hem on and take them off without trouble it wont matter which side it is on. I checked on my JK it is on the Aussie passenger side and I never noticed it giving me any trouble...
Ash74
12-07-11, 09:31 AM
Mani

Cheers
Yer no problem taking them off, so I might just leave it.