Search:

AEM intakes?
http://www.aemintakes.com/

Does it boil over? That is when you know it truly is running 'hot'.

Do you have a winch or big bull bar blocking air flow in front of the grill? Any additional mods we need to know about? Is your...

Larger tires does not give you more suspension lift just further lift from the ground. So you would still have 2" of suspension lift. As long as you aren't going to be playing with the suspension...

0-2". Your springs will settle after time plus the weight of gear/passengers and additional mods down the line ( ie. bumpers, winch, cage) will further compress your springs giving you less lift.
...

If it is spring over then I'm sure the truss only extends to the leaf spring perches and not to the axle flange.

Go here:
http://www.navman.com.au/car-gps-devices/MY-Series/MY75T/Overview/
Click on User Guild
Open up the PDF
from looking at it for only a few minutes it looks like you can save the coordinate...

Pretty common to hit them on everything (and thus cause damage) just because they hang so low. Here is a permanent fix http://www.stu-offroad.com/suspension/rearshock/rearshock-1.htm

Glad to see you got those scout d-44s sold, Chris.

What a nice CJ to be wasted by someone with too little experience and too much of a big head.

There is NOTHING more hardcore on the planet then KOH!
KING OF THE HAMMERS, 2011!
http://www.youtube.com/watch?v=NWcuGt5iefg

You just ran the pump dry. If a JK is anything like a TJ then it has an intank pump (not really all that important, because any vehicle will function effectively the same way with an intank pump,...

Sorry guys but in my book Jeep hasn't made vehicles since 1986.

To have that housing properly tigged you would still have to disassemble the case. There is NO way that you could get the housing clean enough to get a weld free of contaminants with all the...

First thing to check is the bulkhead connector (the brass fitting located at the top of the diff) there are diagrams on ARB site and throughout the web to show you what these look like, but...

Use rockauto for cheap stuff, although they should carry spicer and moog parts, and should still be cheaper with international shipping then some of the crazy prices in Oz.
As for ball joints, I...

I'm familiar with ballistics stuff, I used a lot in my build. They are a great company that makes great products. Are you planning on tieing in the truss to the cover at all? I personally would be a...

I see it has a ballistic fab cover and truss. Did you use their 14 bolt shave kit as well? Did you turn down the ring gear on a lathe as well?

Mani.
These kinda things really suck to diagnose. I think you are on the right track by thinking brakes. It could be grooved/slightly warped/unevenly worn rotors, you could have them machined. It...

Not sure if this applies to you but if your vehicle is 1995 or earlier (OBD I) then you can use a section of 16 gauge wire and a 12 volt test light and get a flash result code reading, then look up...

XJ dana 35 part number 23 is the inner seal

Correction. You are right with the TJs. However, Amc-20 rear ends in the cj series used a dry bearing with both inner and outer seals as well as dana 35 in the yj series 87-95 as well as XJ from...

By rear seal do you mean rear pinion seal or rear axle seal?

The pinion should be substantially cheaper b/c you just have to unbolt the drivehshaft, bust off the pinion yoke, remove the yolk, and...

It would help to know the vehicle?

But they are all about the same. In order to remove the fan shroud you must first remove the clutch fan assembly. There should be a large nut holding the fan and...

grinding at start up sounds like a starter, or flywheel (if it is a manual).

Do you have a welder? It is very tentative but I might be coming back to Sydney. If so I can get this done for ya.